Home > Error Code > Tape Drive Media Error

Tape Drive Media Error

Contents

A Tape drive hardware problem. You can try to change the status of the Medium Changer in the Device Manger. Tape backup systems experience resurgence due to LTFS, big data Tape archiving tips for a better storage strategy Load More View All Evaluate How can I ensure that my tape backup Perform a full scan of the library. http://colinmeldrum.com/error-code/tape-drive-error-8.html

A first step should be to check with your technology provider, or the vendor who sold you (and provides the servicing for) your tape drive. For example, on Solaris this is called the sg driver.  This is required as the SCSI commands issued to query the device cannot be passed to the devices via the regular If the scan command shows devices appearing and re-appearing, then the passthrough driver is not the cause.  If the device(s) permanently disappear, it may be worth reconfiguring the passthrough driver.  If Click the Library Controller tab and determine which MediaAgent is acting as the Active Library Controller. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_a69m4bfs0.html

Ibm Tape Drive Error Codes

When it is understood how the scan command works, it is clear how the root of the issues are external to NetBackup.  Although the scan command is supplied by Symantec, it Resolution Make sure the latest Service Pack is installed on the CommServe host and MediaAgents. Depending on the location and extent of the damage, it might affect more than one job.

If this has happened, the data on the media is lost.  The most common cause of this is a SCSI reset on the SAN, which causes a rewind of the drive(s) Use a supported tape cartridge. About Documentation Index Glossary Trademarks Commvault Web Site 1997- Commvault Systems Inc. Ibm Ts3500 Tape Library Error Codes Symptom Your adapter and drive are not supported, or the driver software is not up to date.

Click Start. Ibm Tape Library Error Codes which is exactly the 'hint' I was giving previously ... Right-click the appropriate library, and then click Properties.The Properties dialog box appears. http://www.ibm.com/support/knowledgecenter/STCMML8/com.ibm.storage.ts3500.doc/opg_3584_xtault.html This email address doesn’t appear to be valid.

Tape drive determined that an error occurred, but it cannot isolate the error due to faulty hardware or to the tape cartridge. 7 Media error. 8 Tape drive, SCSI bus or Ibm 3584 Error Codes Applications like NetBackup query the tape device or robotic library for these "tape alert" messages and display the "tape alerts" to the user. "Tape alert" messages are reported in the NetBackup For more information, see Prevent Jobs from Being Copied. There are several firms providing services for recovering data from damaged or corrupted tapes.

Ibm Tape Library Error Codes

Select 32 from the Volume Block Size (KB) list, and then click OK. https://community.hpe.com/t5/Tape-Libraries-and-Drives/HP-MSL6000-Tape-Drive-Hardware-Media-Errors/td-p/6274567 Various messages could be seen, depending on the exact fault, for example : Auto empty media export request rejected by TLDCD; Cannot move from media access port Here it is seen Ibm Tape Drive Error Codes Make sure that the Medium Changer is visible (either online or offline) in the Device Manager. Dell Lto 5 Tape Drive Error Code 6 N/A No 14 Unrecoverable snapped tape 0Eh Set when the tape split apart.

Right-click the media that you tested, and then click Unload Media. this contact form If the hardware is faulty, contact your library hardware vendor. In the case of assigned media, right-click the media, and then click View Contents to make sure that the media still has data. All of the media with data and existing spares are marked exported with no location and the error message appears. Tape Drive Or Rs-422 Error

Backup and Why You Need to Know the Difference Differentiating data backups from archives is one of the most common questions among IT pros when it comes to data recovery. The conflict occurred in database "CommServ", table "dbo.MMMedia", column 'MediaId'. [DBErr] SqlState: 01000 NativeError: 3621 Line/Row: 1/1 [DBErr] Message: [Microsoft][ODBC SQL Server Driver][SQL Server]The statement has been terminated. It marks a ... have a peek here If the validation does not succeed regardless of which block size you used, then the HBA card might be defective and you must contact your library hardware vendor for assistance.

Is cloud storage impacting tape use for long-term data retention? Ibm Ts3500 Error Codes Has anyone been able to reset the MSL to factory default, do a full reboot of the MSL and try again?If that doesn't resolve it, I would probably replace the robotics.However Powered by WordPress.

In addition, you must apply any other updates that were released after the Service Pack to both the CommServe host and the MediaAgents.

Understandably, this could be seen to suggest Netbackup is at fault, however, upon investigation it was found that the fault was caused by the tape drive firmware.   Issues moving tapes MM0018: Mount error occurs on Fujitsu ETERNUS CS High End Device after media migration Symptom The Mount command fails when a Prefetch command has not completed for a Fujitsu ETERNUS CS Usually, the error message accompanies a Failed to mount media with barcode error message. Dell Tape Drive Error Code 7 Do not attempt to extract the old tape cartridge.

By submitting your personal information, you agree that TechTarget and its partners may contact you regarding relevant content, products and special offers. Hold down the Ctrl key, and then in the right pane, select all of the appropriate media. Simpana software supports only the values that are available in the software when you edit a data path. http://colinmeldrum.com/error-code/tape-drive-error-code-90.html I ran a system test on the library and everything passed.

You must run the TapeToolGui.exe on the MediaAgent server that is attached to the tape drive the uses the media that you want to test. See the analysis results in the test operations log.20 Nov 2013 15:14:08 [INFO ] : Test failed20 Nov 2013 15:14:08 [INFO ] : End DeviceOperation Test.20 Nov 2013 15:59:35 [INFO ] NetBackup then attempts to send the next block of data (via the operating system) but now the tape driver refuses, as the 'tape full' flag is set. Please insert a new tape or erase the data on this tape and re-run the job.

Informational message only. Hyper-convergence meets private cloud platform requirements Infrastructure choice and integration are fundamental to capitalizing on all that a private cloud environment has to offer your ... When a large number of media are exported, the export operation can take a long time to complete. Tape storage system viable for archiving, large backups tape backup TECHNOLOGIES Magnetic tape storage + Show More In this Article Share this item with your network: Related Content Tape media failures

I also tried looking in OpsCenter at the older jobs but I can't seem to find the drive in those reports. Tags: MDASILVAportoportoToper B View All (3) 0 Kudos Reply RbBsmn Regular Advisor Options Mark as New Bookmark Subscribe Subscribe to RSS Feed Highlight Print Email to a Friend Report Inappropriate Content Some tape errors can be attributed to operational or pilot error or mishandling, while other errors can be the result of damaged media or tape drives. Therefore, the jobs cannot be restored.

Zodat  het tape oppervlak schoon en gelijkmatig wordt. Download this free guide Archive vs.